3/8 x 24 Threaded Base.
100 % American Made. Double insulated 19 Gauge Copper Wire. Adjustable Tuning Range. 144-148MHZ Range 1.5:1 SWR. |
Coax Cable w/Low-Profile Fire-Ring and Stud
Length - 18 feet Coax Connectors - PL-259 (requires soldering) to Firering low-profile antenna stud Impedance - 50 ohm |
18' (5.5m) RG-58A/U Fire-Flex PL to Lug
Stranded center conductor to maximize flexibility and prevent untimely breakage Shielding coverage that averages 95% to protect against RF leaks and interferrence Polyvinyl center insulation for ruggedness and longevity Performance that exceeds mil-spec requirements for 50 ohm RG-58A/U coax |
Quality 18' coax made right here in the USA
Dual PL-259 (barrel connector) ends Compatible with: All CB radios and mount studs that accept a PL-259 coax connection. |
Fire-Flex dual antenna coax cable
CO-PHASE 18' CB RADIO COAX W/ 4 LUGS & 1 PL259 CONNECTOR STRANDED CENTER CONDUCTOR 95% AVERAGE SHIELDING HEAVY DUTY CONNECTORS |
Fire-Flex dual antenna coax cable
Stranded center conductor to maximize flexibility and prevent untimely breakage. Shielding coverage that averages 95% to protect against RF leaks and interferrence. Polyvinyl center insulation for ruggedness and longivity. Performance that exceeds mil-spec requirements for 75 ohm RG-59A/U coax. |
2"e; (61cm) Firestik II Heavy-Duty -Antenna 5/8 Wave (Blue)
5/8 Wave Length Design Rated @ 300 Watts Can be Used in Single or Dual Configurations Requires Fine Tuning (SWR) Easy-Tune Bare-Hands Tunable Tip Hi-Performance Loading Coil |
2FT(61CM) SINGLE MIRROR NGP KIT COMPLETE
No ground plane antenna system Ideal for fiberglass vehicles like RV's and Semi Trucks Includes all necessary components 3' 5/8 wave antenna 17' specialty no-ground coax cable Tunable Tip Full 40 Channel CB operation |
5/8 Wave Length Design
Rated at 100 Watts Can be Used in Single or Dual Configurations Requires Fine Tuning (SWR) Hi-Performance Loading Coil 3/8 x 24 Threaded Base with Tapered Contact End Custom Blended Glass Fiber Reinforced Shaft Wound with Heavy Insulated Copper Wire Static Reducing Water-Tight Sleeve Containing UV & Pigment Stabilizers |
40 channel plus CB antenna.
Low-cost money saver. Lightweight. Moderate power handling. Flexible fiberglass whip. 100% American made with 100% American materials. Custom blended, glass fiber reinforced tube. Wound with double insulated copper wire to prevent the oxidation and shorted windings. 3/8 -24 threaded base will fit all Firestik and RoadPal mounts and accessories. Covered with a static reducing, water-tight sleeve containing UV and pigment stabilizers. Factory bench tested for resonant frequency and overall quality. Color: White. |
5' Hand Tune Fiberglass CB Antenna - BLACK
Power Handling-1000 Watts Works with all CB radios-Cars, trucks, RV's motorcycles, vans, semi's, and more... Average tuned SWR-1.5 Works on either single or dual antenna configurations Standard 3/8 x 24in thread All mode operation-AM/FM/SSB and NOAA Alert Tunable Tip-Tune by hand, no tools needed! Static reduction cap, eliminates up to 50% of noise Recommend 18ft coax cable 5 Year Manufacturer Warranty 5/8 Wave Antenna Top Loaded Design |
Indoor CB base antenna
This base antenna can be set up inside a home, on a job site or anywhere that requires a temporary base station Just over 5' tall, (4) 30"e; radials, easily transportable Range: Approximately 1 to 3 miles used indoors; Approximately 3 to 5 miles used outdoors Product Includes: Firestik IBA-5 base antenna 18' Fire-Flex coax cable |
Coax Adapter, UHF PL-259 to BNC
BNC Male to PL-259 Female Adapter/Connector Allows you to connect a hand-held CB to a standard roof mount antenna Fits all handheld CB radios |
ADUSTABLE HOOD / TRUCK / HATCH CB RADIO ANTENNA MOUNT KIT
18 ft (5.5m) of professional grade Fire-Flex coaxial cable (with a Fire-Ring connector) The PL-259 connector is supplied but not installed. This allows the coax to be routed through a smaller hole After the connector has been installed the coax center conductor needs to be soldered to the connector For antennas up to 4' (1.2m) |
Double Female UHF Female Barrel Connector PL259
Use this connector to join two, PL-259 terminated coax cables together when additional length is required Double Female UHF Barrel Connector |
Replacement Antenna Tips
For FireStik II (FS Series) Antennas Black Sold: Pkg of 2 |
Universal flat edge mount with K-4 stud with lugs.
Constructed of high quality stainless steel. May be used as hood channel mount on late model (1995 and up) Dodge RAM trucks or on a flat surface, bed rail, or bumper. Accommodates 3/8-24 antenna. |
DODGE RAM / DAKOTA CB RADIO ANTENNA HOOD MOUNT (1994-2004
stainless steel mount is for antenna installation on the 1994 thru 2004 Dodge Ram and Dakota pick-ups (due to body changes made in 2005, this mount will not fit 2005 and newer vehicles). When the hood is open, the fender bolt nearthe firewall is removed (right or left side) and later reused to bolt the antenna bracket to the under-hood fender lip. All mounting hardware is invisible unless the hood is open. The bracket has a pre-determined bendand does not interfere with the closing of thehood. The bracket is2"e; (51mm) wide by 4.1"e; (104mm) long. |
Adjustable stainless steel vertical door jamb mount
Designed to allow antenna installations on vehicles where other mounts may not work The bracket is 1.5"e; (38mm) wide and has a 2"e; (50mm) reach for mounting inside the door jamb. |
Tune Tip Kit For Firestik Firefly Series CB Antennas
Includes Brass Tuning Screw, Jam Nut, Rubber O-Ring & New Plastic Cap |
Screw-On Flat Universal CB Antenna Mount Stainless Steel
|
B RADIO ANTENNA SPRING CHROME PLATED HEAVY DUTY
3/8"e; X 24 ANTENNA THREADS FOR ANTENNAS UP TO 60"e; TALL SPRING IS ABOUT 3"e; TALL |
Stainless Steel Hood/Trunk Channel Mount
Stainless steel construction Mounts to the inside channel of your hood or trunk using included hardware/stud Mounting hardware is hidden inside the hood or trunk channel Compatible with most vehicles that have a hood and/or trunk, in channels up to 2"e; deep 2.1"e; from mounting base to first bend, 2.9"e; from mounting base to top of bracket |
IN-LINE UHF LIGHTENING & STATIC ARRESTOR
For Mobile or Base Operation Easy to Install Offers Low Resistance Path to Ground from Atmospheric Static and Electrical Charges |
This mag mount is a great choice for mounting your antenna to a roof, trunk or other flat surface
Adhesive-backed disk keeps your vehicle's paint job intact Recommended for: Mounting a standard 2' or light 3' antenna on the flat metallic surface of a truck, car, SUV or other vehicle. Compatible with: All fiberglass and center-load antennas that use a standard 3/8"e; x 24 threaded base. Stud Type: PL-259 (Barrel) Product Includes: 4.9"e; magnet mount and 18' of coax cable CB antenna not included |
Stainless steel 3-way mounting brackets
Stainless Steel Bracket and Clamp Includes Screw-On K-4A Antenna Stud Designed to Mount Antennas Horizontal or Vertical Can be Mounted without Clamp on any Flat Vertical Surface Complete with Stainless Steel Mounting Hardware For Firestik Antennas Up to 5 The actual size of the bracket is 2.25"e; (57mm) wide by 2.9"e; (74mm) high |
Molded Side Mount with 18 ft. Fire-Flex Coax -W-Lugs
For single vertical side antenna installs Includes molded side mount and 18 Foot Fire-Ring Coax Use with antennas up to 4 Feet Tall |
Pickup truck stake hole cb antenna mount
Mount locks into any of the stake hole pockets along the edge of a pick-up truck bed No need to drill any holes in the vehicle Accepts 3/8-24 thread antennas up to 4 Feet Includes K-4A stud and stainless steel bracket 100% American made with 100% American materials |
CB Antenna Stud Threaded Plug
sold in a pack of 2 Works To Keep Moisture and Dirt From Antenna Stud When Antenna Not Installed |
|
|
|
|
Copyright © 1999-2022 BuilderDepot, Inc. Site Designed and Maintained by Inline Internet Systems, Inc. |