FENCE BRACKET
Connects solid fence rail to post easily
Eliminates need to notch posts
Can be nailed to post before posts are set
FB14-TZ 1X4 FENCE BRACKET
SIZE:3/4 x 3-1/2"
FIT:1 x 4" Rail
|
4-SIDED GALVANIZED POST ANCHOR
Provides 1" elevation above concrete
Keeps post off concrete and dryer
Large pre-punched opening for anchor bolt
18 gauge galvanized body w/triple-zinc coating
14 gauge galvanized steel base & washer
Nails not included
PA44-TZ 4X4 4-SIDE POST ANCHOR
SIZE:3.5x 3.56x 2.13"
FIT:4 x 4" Post
|
18 GAUGE FRAMING ANGLE CLIP
A3 series - 18 gauge frame angle clip
Eliminates toenailing & increases strength
A3 1-7/16X2-3/4 ANGLE CLIP
SIZE:1.5x 1.5 x 2.75"
FINISH:Galvanized
|
FRAMING ANGLE CLIP
Features staggered nail patterns which -
reduces wood splitting
Allows installation on both sides of -
supported member
supported member
AC5 4-7/8 IN. FRAMING ANGLE CLIP
SIZE:4-7/8"
|
POST CAP
1-piece design post cap
For light-duty post-to-beam connection
Quick and easy installations
18 gauge galvanized steel
C44-TZ 4X4 POST BEAM CAP
FIT:4 x 4" Post
FINISH:Triple-Zinc
|
COMPOSITE POST BASE
Made of corrosion resistant composite material
Compatible with new wood preservatives
Provides code required for 1" stand-off
Can be used with rough lumber sizes
CPB44 4X4 COMPOSITE POST BASE
FIT:4 x 4" Post
|
COMPOSITE POST BASE
Made of corrosion resistant composite material
Compatible with new wood preservatives
Provides code required for 1" stand-off
Can be used with rough lumber sizes
CPB66 6X6 COMPOSITE POST BASE
FIT:6 x 6" Post
|
DECK BRACKET
Eliminates toe-nailing
Secures wood post/column to wood decking
Attaches to concrete with anchor bolt
18 gauge galvanized steel
Triple zinc coating for ACQ treated wood
D44-TZ 4X4 DECK BRACKET
FIT:4 x 4" Post
FINISH:Triple-Zinc
|
ELEVATED POST BASE
Allows installers to pre-align post & preset-
post heights above concrete floors or footings
By eliminating post-to-concrete contact, -
moisture damage is reduced
Galvanized, triple-zinc coating for ACQ wood
16 ga tube w/16 ga steel u-bracket
3-9/16"W x 2-3/4"L x 2-3/8" and 7-1/2" heights
Coverage depends on surface type and porosity
EBG44-TZ 4X4 ELEVATE POST BASE
FIT:4 x 4" Post
FINISH:Galvanized
|
PROTECTION PLATE
16 gauge steel conforms to protection -
shield plate requirements of NEC & IPC
G185 galvanized
Easy-to-install plates protect plumbing & -
power/communication wiring from nails/screws
ICPL516TZ 16-1/4X5 PROT PLATE
SIZE:1/4" x 5" x #16
FINISH:Galvanized
|
INSULATION SUPPORT
Secures batt insulation between joists
Chisel cut ends dig into joist for -
permanent holding
Easy to install in hard-to-reach spaces
IS16 16 IN. INSULATION SUPPORT
SIZE:16" x #13
|
INSULATION SUPPORT
Secures batt insulation between joists
Chisel cut ends dig into joist for -
permanent holding
Easy to install in hard-to-reach spaces
IS24 24 IN. INSULATION SUPPORT
SIZE:24" x #13
|
2X6 SINGLE PURLIN HANGER
Attaches 2x6 cross member to roof trusses
18 gauge G90 galvanized steel
1-9/16"W x 5-1/2"H x 3/4" top face
JDS26S 2 IN. X6 IN. PURLIN HANGER
SIZE:2 x 6" x #18
|
JOIST HANGERS
Hangers have Grip Tooth speed prongs
For setting hanger in position for nailing
JL210 2X10 12-14 JOIST SUPPORT
SIZE:2"x10"x 12/14 ga
|
JOIST HANGERS
Hangers have Grip Tooth speed prongs
For setting hanger in position for nailing
JL24 2X4 20 GA JOIST HANGER
SIZE:2"x4"x #20
|
JOIST HANGERS
Hangers have Grip Tooth speed prongs
For setting hanger in position for nailing
JL26 2X6-8 JOIST SUPPORT
SIZE:2"x6"x #8
|
JOIST HANGERS
Hangers have Grip Tooth speed prongs
For setting hanger in position for nailing
JL28 2X8-10-12 JOIST SUPPORT
SIZE:2"x8"x 10/12 ga
|
SLANT NAIL DOUBLE JOIST HANGERS
Double shear nail design
Use standard length nails
Patented dimple allows 30-45 degree nailing
Triple-zinc coated for ACQ treated lumber
3-1/8" wide x 2" deep
JUS210-2TZ 2X10DBL JOST HANGER
SIZE:9-1/8" x #18
FIT:(2) 2 x 10"
|
SLANT NAIL JOIST HANGERS
Double shear nail design
Use standard length nails
Patented dimple allows 30-45 degree nailing
Triple-zinc coated for ACQ treated lumber
1-9/16" wide x 1-3/4" deep
JUS210-TZ 2X10 JOIST HANGER
SIZE:7-3/4" x #18
FIT:2 x 10"
|
SLANT NAIL JOIST HANGERS
Double shear nail design
Use standard length nails
Patented dimple allows 30-45 degree nailing
Triple-zinc coated for ACQ treated lumber
1-9/16" wide x 1-3/4" deep
JUS24-TZ 2X4 JOIST HANGER
SIZE:3-1/8" x #18
FIT:2 x 4"
|
SLANT NAIL DOUBLE JOIST HANGERS
Double shear nail design
Use standard length nails
Patented dimple allows 30-45 degree nailing
Triple-zinc coated for ACQ treated lumber
3-1/8" wide x 2" deep
JUS26-2TZ 2X6 DBL JOIST HANGER
SIZE:5-1/4" x #18
FIT:(2) 2 x 6"
|
SLANT NAIL JOIST HANGERS
Double shear nail design
Use standard length nails
Patented dimple allows 30-45 degree nailing
Triple-zinc coated for ACQ treated lumber
1-9/16" wide x 1-3/4" deep
JUS26-TZ 2X6-8 JOIST HANGER
SIZE:4-13/16" x #18
FIT:2 x 6-1/8"
|
SLANT NAIL DOUBLE JOIST HANGERS
Double shear nail design
Use standard length nails
Patented dimple allows 30-45 degree nailing
Triple-zinc coated for ACQ treated lumber
3-1/8" wide x 2" deep
JUS28-2TZ 2X8-10DBL JOS HANGER
SIZE:7-1/8" x #18
FIT:(2) 2 x 8"
|
SLANT NAIL JOIST HANGERS
Double shear nail design
Use standard length nails
Patented dimple allows 30-45 degree nailing
Triple-zinc coated for ACQ treated lumber
1-9/16" wide x 1-3/4" deep
JUS28-TZ 2X8 JOIST HANGER
SIZE:6-5/8" x #18
FIT:2 x 8"
|
KSN1 PROTECTION PLATE
Easy-to-install protection plate
Protects plumbing & electrical lines
Protects cables for intercoms & alarm systems
Provides barrier against nails & screws
KNS1 1.5X3 PROTECTION PLATE
SIZE:1-1/2 x 3"
|
MULTI-PURPOSE FRAMING ANGLE
Tab enables two and thee-way connections
Engineered to strengthen framing
18 gauge galvanized steel
Triple-zinc coating for ACQ treated wood
Dimensions: 1-1/2" x 1-7/16" x4-1/2"H
MPA1-TZ 1-3/8X4.5 FRAME ANGLE
SIZE:1-3/8 x 4-1/2"
FINISH:Triple-Zinc
|
GALVANIZED NAIL PLATE
Increases support and stability
Not for use in truss manufacturing
Use 8d common or 8d x 1-1/2" nails
NP15 5X1-13/16 MENDING PLATE
SIZE:5"x1-3/16"x #20
FINISH:Galvanized
|
GALVANIZED NAIL PLATE
Increases support and stability
Not for use in truss manufacturing
Use 8d common or 8d x 1-1/2" nails
NP35 3.125X5 TIE PLATE
SIZE:5"x1-3/8"x #20
FINISH:Galvanized
|
GALVANIZED NAIL PLATE
Increases support and stability
Not for use in truss manufacturing
Use 8d common or 8d x 1-1/2" nails
NP37 7X3-1/8 MENDING PLATE
SIZE:7"x3-1/8"x #20
FINISH:Galvanized
|
GALVANIZED NAIL PLATE
Increases support and stability
Not for use in truss manufacturing
Use 8d common or 8d x 1-1/2" nails
NP39 3.125X9 TIE PLATE
SIZE:9"x1-3/8"x #20
FINISH:Galvanized
|
GALVANIZED NAIL PLATE
Increases support and stability
Not for use in truss manufacturing
Use 8d common or 8d x 1-1/2" nails
NP57 5X7 MENDING PLATE
SIZE:7"x5-3/4"x #20
FINISH:Galvanized
|
POST ANCHOR
2-sided post anchor
Provides 1" elevation above concrete
Elevation help keep post dry
Large pre-punched opening for anchor bolt
18 gauge galvanized steel body
14 gauge galvanized steel base & washer
Triple-zinc coating for ACQ treated wood
PA44E-TZ 4X4 POST ANCHOR
FIT:4 x 4" Post
FINISH:Triple-Zinc
|
|
|
|
|
Copyright © 1999-2022 BuilderDepot, Inc. Site Designed and Maintained by Inline Internet Systems, Inc. |